Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
Are you trying to locate advise around Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and also often, tiling skills. Changing an old tub with a new one is additionally a reasonably difficult task. If the old bathtub is easily available, the task can move speedily; if you need to open a wall surface to eliminate the old bathtub and also position the new bath tub, the job is much harder. In either instance, the project is within a home handyman's abilities, although you will require an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the work as well as fit attempting it. As opposed to employing a contractor to take over a halfway-completed task, it is much better to consider employing one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This article will aid you set up a brand-new bathtub in your shower room if you have actually already acquired a new bathtub and also do not need to transform the setup of your previous supply of water pipelines.
Your devices and also product checklist ought to consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing faucets can be quite problematic due to the limited accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The former type needs to be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using both wooden boards under its feet, position the tub in the required setting. The wooden boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to make certain that the bathtub is leveled all round. This can be attained by examining the spirit level and also adjusting the feet on the bath tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water and also check all joints as well as new pipework for leaks and also tighten them if required. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will certainly settle it into its last position.
Getting ready for the Setup
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last position.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to difficulties with wetness as well as feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can crack rather early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on Tools You Need to Install a New Bathtub ? Try to leave a remark directly below. We will be delighted to know your reactions about this post. Hoping that you visit us again in the future. You should take a moment to distribute this blog posting if you appreciated it. Bless you for your time. Kindly check up our blog back soon.
Visit Our Site
Report this page